鋁板在各行各業中使用非常廣泛，它是一種很受歡迎的建筑裝飾材料，在使用鋁板時，肯定會遇到一些問題，下面鋁板生產廠家就說一下鋁板使用過程中的九個注意事項。
Aluminum plate is widely used in all walks of life. It is a very popular building decoration material. When using aluminum plate, there will certainly be some problems. The aluminum plate manufacturer will talk about nine precautions during the use of aluminum plate.
一、鋁板貯存:應將板材存放于干燥通風處,且平放在平整的表面上,切勿踩踏、撞擊。
1、 Storage of aluminum plates: The plates shall be stored in a dry and ventilated place, flat on a flat surface, and shall not be stepped on or struck.
二、鋁板搬運:搬運板材應將板的四邊同時抬起,嚴禁推拉、抽取,以免刮傷板面。
2、 Aluminum plate handling: when handling the plates, the four sides of the plates shall be lifted at the same time. It is strictly prohibited to push, pull or extract the plates to avoid scratching the surface.
三、鋁板開槽:用開槽機或鑼機開槽時,應使用半圓頭式大于90度的銑刀.下刀既不要過深傷及鋁板,也不要過淺使折邊困難,應留有0.2-0.3MM厚塑料芯材連同鋁板一起彎邊,以增加強度和韌性,否則在彎邊時鋁板可能斷裂或漆膜爆裂。
3、 Aluminum plate slotting: When slotting with a slotting machine or a gondola machine, a semicircle head milling cutter larger than 90 degrees should be used. The cutting tool should not be too deep to damage the aluminum plate, nor too shallow to make folding difficult. A 0.2-0.3MM thick plastic core should be left with the aluminum plate bent together to increase strength and toughness, otherwise the aluminum plate may break or the paint film burst when bending.
四、鋁板彎邊:彎邊時需用力均勻,一次成型,不要反復彎折,否則鋁板可能斷裂。
4、 Aluminum plate bending: the bending force shall be uniform, forming at one time, do not bend repeatedly, or the aluminum plate may break.

五、鋁板弧形加工:加工弧形應使用專用彎曲設備加工,徐徐用力,使板材逐步達到所需的曲面.切勿一次彎曲成型。
5、 Arc processing of aluminum plate.
六、鋁板批次:同一型號而不同批次的板材可能存在色差,出售和使用不同批次板材時應增加比對色差之程序，我們公司主要經營合金鋁板、鋁花紋板等，無視覺色差時方可在同一平面使用。
6、 Aluminum plate batch: The plates of the same model but different batches may have color difference. When selling and using different batches of plates, the procedure for comparing color difference should be added. Our company mainly deals in alloy aluminum plates, aluminum pattern plates, etc., and can only be used on the same plane when there is no visual color difference.
七、鋁板安裝方向:將同色鋁板安裝在同一平面時,流程方向應一致,否則可能造視覺色差。
7、 Aluminum plate installation direction: when installing aluminum plates with the same color on the same plane, the flow direction should be consistent, otherwise visual color difference may occur.
八、鋁板撕膜:應在鋁板安裝后的45天內撕去保護膜,否則可能發生撕膜困難或移膠現象。
8、 Tearing film of aluminum plate: the protective film shall be removed within 45 days after the installation of aluminum plate, otherwise it may be difficult to tear the film or remove the adhesive.
九、鋁板使用條件:內墻板應在室內使用,不宜安裝在室外,以保證使用效果和使用年限。
9、 Service conditions of aluminum plate: the interior wallboard shall be used indoors rather than installed outdoors to ensure the service effect and service life.
此外由于鋁板的不斷地火熱，在市場上出現了各種各樣的鋁板產品的，每個廠家都介紹自己品質好，的確讓人難以選取，所以在購買的時候要多方面進行考慮。更多相關內容就來我們網站http://www.gdjsdtc.com進行咨詢吧！
In addition, due to the continuous popularity of aluminum plates, a variety of aluminum plate products have appeared in the market. Each manufacturer has introduced their good quality, which is really difficult to choose. Therefore, we should consider many aspects when purchasing. More relevant content will come to our website http://www.gdjsdtc.com Consult!